Used Padfoot Wheel Style Excavator Compaction Wheel suit 9-16 Ton machines.
*** The Good:
* 80mm pads for deep penetration.
* Pads are all there, in great shape with minimal wear.
* Bearings roll smooth and easily.
* Structurally solid with plenty of life left.
*** The Bad:
* There is a buckle in the main horizontal shaft. The tips of the pads have about 26mm of left-right deflection (roll half turn = 13mm from center, roll another half turn and is now 13mm from center to the other side (see bottom of the middle wheel in Pic# 6)).
* There is some rust pitting on one face from where it had been laid on its side with water pooled (see pics# 4-5). This is minimal and will not affect the performance as the wheel plate is quite thick.
Although not perfect, this wheel is solid and still very functional. The price has been reduced.
*** Wheels:
* Each Wheel Width: 65mm
* Total Compaction Width of the 3 wheels: 380mm
* Wheel Diameter: 532mm
* Wheel Diameter Total (including pads): 694mm
*** Each Pad:
* Height: 80mm
* Size at Top: 48mm wide x 50mm long
* Size at Base: 50mm wide x 95mm long
Dimensions (standing up): 424mm Wide, 694mm Deep, 944mm High. Weight: 320kg.
*** Current Headstock configuration:
* Pin Diameter: 60mm.
* Pin Center to Pin Center (CtoC): 374mm.
* Between the Ears (BTE): 277mm between the Bosses (which can be shaved back up to 311mm between the Ear Plates if you need more inside width for your hitch or dipper arm to fit in).
*** 60mm Pin Configuration (Current):
*
* Should fit: Kobelco SK100 / SK100LC / SK115SR, Komatsu PC100-3 / PC100-5 / PC100-6 / PC120 / PC120 Mighty / PC120-3 / PC120-5 / PC120-6 / PC128US-2 / PC128UU-2 / PC138USLC-2 / PC150HD / PC158USLC-2 / PW100-1 / PW100-3, Liebherr 912, New Holland EC160LC / EW160 / EW200 / FX140 / FX200, Volvo EC160 / EC160 Direct Mount / EW160 / EW160 Direct Mount.
*
* Maybe fit: Caterpillar 205 / 206 / 211 / 212, Hydrema M1100, Kato 550SEV, New Holland EC130LC, O & K MH & RH 4CS / O & K MH 2-12.
*** As an 65mm Pin Configuration (See Mod suggestions below):
*
* Should fit: Case 9013 / CX130 / CX135 / CX135SR, Kobelco K905 / SK120 / SK130 / SK130LC / SK135 / SK135SR, Link-Belt 130LX / 135SA / 2650 QUANTUM, Samsung SE130-3 / SE130LC-3 / SE130W / SE130W-3, Sumitomo SH100 / SH100-2 / SH100CT-2 / SH120 / SH120-2 / SH120CT-2 / SH135U-2 / SH135X-2 / SH145U / SH200LC-3LR, Terex TXC 140LC-1, Volvo EC130-3 / EC140 / EC140B / EC140C / EC140D / EC145D / EC210C LR / EC290C LR / ECR145C / EW130 / EW140C / MX135WS/LS / SE130W-3/LC-3.
*
* Maybe fit: Caterpillar 311 / 311C / 311D / 312 / 312B / 312C L / 312D / 313 / 314C LCR / 314D / 320D, Daewoo Solar 130LC-V / 130W-2 / 130W-3 / 130W-V / 140LC-V, Doosan DX140LC-3 / DX140W / DX140W-3 / DX300LC-3 SLR / S130LC-V / S140LC-V / S140W-V / S255SLR / S300SLR, Halla HE130W, Hitachi EX110-5 / EX120-2 / EX120-3 / EX120-4 / EX120-5 / EX135 / EX135UR, Hitachi Zaxis 135US, Hyundai R120 / R130LC / R130LC-3 / R130W / R140LC-7, JCB 805B / 814S / JS110 / JS130 / JZ140, John Deere 135C RTS, Kato HD 512, Sumitomo SH120-3 / SH125-3 / SH125X-3 / SH130-5 / SH135-3 / SH135X-3, Takeuchi TB 1140, Yuchai YC135-7.
For light or infrequent work, it will work as-is in a 65mm pin Hitch.
For heavy duty or regular work, best to set the wheel up to 65mm pins to prevent wear to your hitch, by either:
1.) Bore the Pin holes:
Remove the 60mm pins, bore out the holes to 65mm, insert 65mm pins.
or...
2.) Sleeve the Pins:
Using 65mm OD (Outside Diameter) pipe/tube with 60mm ID (Inside Diameter).
Cut 2 lengths to 276mm long each. Remove the pins, put each tube in place where the pin was (between the Pin Bosses), bash the pins back in so they are sleeved by the tube.
or...
3.) Fatten up the pins where your hitch touches:
Cut out some plates of 2.5mm thick sheet steel. Weld one edge of each plate to the pins around where your hitch makes contact with the pin.
Hammer the plates so they curve around the pin, finish welding the remaining 3 edges of each plate (you may need to use a G-Clamp to ensure the plates are fully contacting the pin before the final welds). Grind any excess weld smooth.
This simulates the pins being 65mm thick just where the hitch actually grabs the pin.
Call if you would like to discuss or to come inspect it.
We are at Pullenvale, 16km west of Brisbane CBD, between Brookfield and Anstead, near Kenmore.
You can pick up, we can deliver to a reasonable distance for an agreed fee, or we can arrange freight within Australia.